Cords on sash windows can break over time. It does not have to cost a lot of money to repair them. In fact, one can do so themselves without any experience or expertise in home improvement. The following tips will teach people How to change a broken cord on a sash window.
The first thing one will have to do is gather tools for this repair job. Some of the tools needed are a lubricant, a screwdriver and a utility knife. Other tools are a putty knife, new roping for the window cord and a hammer. Once the tools are in hand, the next step is to remove the window from the frame.
After the window is removed, the sash cord needs to be accessed. Some windows have access panels. Older windows, on the other hand, may not have them. If that is the case, then the window casing must also be removed.
The first step is in getting to the sash cords. Those windows that have an access panel will have it on the side jambs. Inside the panel are the weights, the pulleys and the sash. At the time that access is made, any old cord on the sash weights and the weights themselves need to be taken out. Once the cord roping is detached, put the weights back. They should be put on top of a wood block that is four to five inches thick.
The next step is to lubricate the window pulleys. Make sure they are clean first. If not, clean them before spraying with a lubricant. Following that step, do what it takes to make feeding the rope through the pulley easier. One way to do this is to tape the end of the new cord to the end of the old cord. Of course, the next step is to feed the rope through the pulley. Withdraw the old cords from the access panel. As the old cords are removed, the new cords will be fed through the pulley.
Sash weights contain a hole. The cord should be run through the hole in the weights. Tie a knot at the bottom of the cord roping. The rope will usually go two or three inches past the pulley. Do the same steps as were done on this side to the other side. Then, add trim and finish nails. Additionally, stain and finish can be added to fit the home's decor and atmosphere.
It is not necessary to be a home improvement professional in order to fix a broken sash window cord. It also does not take much time. A little bit of time in an afternoon, the proper tools and the correct instructions will make changing cords possible. Follow these steps and one will know How to change a broken cord on a sash window.
The first thing one will have to do is gather tools for this repair job. Some of the tools needed are a lubricant, a screwdriver and a utility knife. Other tools are a putty knife, new roping for the window cord and a hammer. Once the tools are in hand, the next step is to remove the window from the frame.
After the window is removed, the sash cord needs to be accessed. Some windows have access panels. Older windows, on the other hand, may not have them. If that is the case, then the window casing must also be removed.
The first step is in getting to the sash cords. Those windows that have an access panel will have it on the side jambs. Inside the panel are the weights, the pulleys and the sash. At the time that access is made, any old cord on the sash weights and the weights themselves need to be taken out. Once the cord roping is detached, put the weights back. They should be put on top of a wood block that is four to five inches thick.
The next step is to lubricate the window pulleys. Make sure they are clean first. If not, clean them before spraying with a lubricant. Following that step, do what it takes to make feeding the rope through the pulley easier. One way to do this is to tape the end of the new cord to the end of the old cord. Of course, the next step is to feed the rope through the pulley. Withdraw the old cords from the access panel. As the old cords are removed, the new cords will be fed through the pulley.
Sash weights contain a hole. The cord should be run through the hole in the weights. Tie a knot at the bottom of the cord roping. The rope will usually go two or three inches past the pulley. Do the same steps as were done on this side to the other side. Then, add trim and finish nails. Additionally, stain and finish can be added to fit the home's decor and atmosphere.
It is not necessary to be a home improvement professional in order to fix a broken sash window cord. It also does not take much time. A little bit of time in an afternoon, the proper tools and the correct instructions will make changing cords possible. Follow these steps and one will know How to change a broken cord on a sash window.
About the Author:
Looking for comprehensive info on how to change a broken cord on a sash window ? Get the exclusive low down instantly in our complete overview of sash cord repairs and all you need to know about sash window repairs London .
0 comments:
Post a Comment
Loading...